1 x 4 4K HDMI to DM 8G+ and HDBaseT Splitter
Model: DM-DA4-4K-C
Part #: 6507981
- Converts and splits one HDMI® input to four DM 8G+® outputs
- Single HDMI output enables cascading to additional units
- Supports 4K UHD and DCI 4K video at 60 Hz
- Handles Dolby® TrueHD, Dolby Atmos®, DTS-HD®, DTS:X®, and uncompressed 7.1 linear PCM audio
- Passes the AV signal to all outputs without change or degradation
The DM-DA4-4K-C is a DigitalMedia™ accessory that converts and splits a single 4K60 HDMI® signal to feed four separate DM 8G+® or HDBaseT® receivers. A single HDMI output is included to pass the input through to a local display, audio processor, switcher, or another DM-DA4-4K-C. Video and audio are passed from the input to all five outputs simultaneously without any change or degradation.
PoDM+ and HDBaseT PoE+ power sourcing is enabled at all four DM® ports by adding a PoDM power supply (model PW-4830DUS or DM-PSU-3X8-RPS, sold separately). This enables certain DM receivers and HDBaseT devices to receive power through the CATx cable, eliminating the need for a separate power supply at each endpoint location.
A Gigabit Ethernet port is included to provide a single-point LAN connection for all connected devices, including DM receivers and HDBaseT devices. Gigabit connectivity at the DM-DA4-4K-C ensures a full 100 megabit connection for each connected device.
HDCP is globally selectable on the DM-DA4-4K-C to support version 2.2, 1.4, or none. EDID functionality is configurable to either pass EDID to the input from the device connected to the first DM output port, or to use a pre-fined default EDID optimized for 1080p60. CEC signals are not passed through the DM-DA4-4K-C, although most DM receivers can support CEC through integration with a control system via Ethernet.
One or two DM-DA4-4K-C units can be rack-mounted in a single rack space using the ST-RMK rack mount kit. Installation beneath a table or counter is enabled using the UTK-1U-HALF under-table mounting kit.
- Converts and splits one HDMI® input to four DM 8G+® outputs
- Single HDMI output enables cascading to additional units
- Supports 4K UHD and DCI 4K video at 60 Hz
- Handles Dolby® TrueHD, Dolby Atmos®, DTS-HD®, DTS:X®, and uncompressed 7.1 linear PCM audio
- Passes the AV signal to all outputs without change or degradation
- Simple setup, no programming required
- Compatible with HDBaseT® certified equipment
- Selectable HDCP 2.2 or 1.4 compliance
- Supports PoDM+ and HDBaseT PoE+ power sourcing
- Provides LAN connectivity for DM 8G+ receivers
- Supports Ethernet over HDBaseT
- Single-space, half-width 19-inch rack-mountable
- Under-table mountable
- Universal 100-240V external power pack included
- Combiner Type - Splitter/Combiner
- HDBaseT - Yes
- Rackmountable - Yes
- TX RS-232 - No
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Number of Inputs: 1
- Number of Outputs: 4
- Rack Units (Height): 1
- AC Voltage (Maximum): 240 Volts
- AC Voltage (Minimum): 100 Volts
- Current Draw: 1.25 Amps
- DC Voltage: 24 Volts
- Depth: 9.19 in
- Height: 1.70 in
- Width: 7.07 in
- Product Weight: 3.20 lbs
- Regulatory Compliance: HDCP
- Video:
•Input Signal Types: HDMI with Deep Color, 3D and 4K (DVI and Dual-Mode DisplayPort compatible)
•Output Signal Types: DM 8G+ and HDBaseT with Deep Color, 3D and 4K, HDMI with Deep Color, 3D and 4K (DVI compatible) - Audio:
•Input Signal Types: HDMI (Dual-Mode DisplayPort compatible)
•Output Signal Types: DM 8G+ & HDBaseT, HDMI
•Formats: Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels - COMMUNICATIONS:
•Ethernet: 10/100/1000 Mbps, provides a single-point LAN connection for four DM or HDBaseT devices
•USB: USB host for firmware update via USB mass storage device
•DigitalMedia: DM 8G+, HDCP 2.2 or 1.4 HDCP, EDID, CEC, PoDM, PoDM+, 100 Mbps Ethernet
•HDBaseT: HDBaseT Class A, HDCP 2.2 or 1.4 HDCP, EDID, PoE, PoE+, 100 Mbps Ethernet
•HDMI: HDCP 2.2 or 1.4 HDCP, EDID - Connectors:
•LAN: (1) 8-pin RJ45 female
•10Base-T/100Base-TX/1000Base-T Ethernet port
•PoDM INPUT: (1) Combo D-Sub 7w2, male
•48 Volt DC power input for PoDM power supply
•Enables PoDM+ power sourcing on each DM OUTPUT port
•SERVICE: (1) USB Type A female
•Supports USB mass storage devices for firmware update
•24VDC 1.25A: (1) 2.1 x 5.5 mm DC power connector
•24 Volt DC power input
•PW-2412WU power pack included
•HDMI INPUT: (1) 19-pin Type A HDMI female
•HDMI digital video/audio inputs
• (DVI & Dual-Mode DisplayPort compatible)
•HDMI OUTPUT: (1) 19-pin Type A HDMI female
•HDMI digital video/audio output (DVI compatible)
•DM OUTPUT 1 – 4: (4) 8-pin RJ45 female, shielded
•DM 8G+ outputs, HDBaseT compliant
•PoDM+ PSE ports (HDBaseT PoE+ compatible)
•Each connects to the DM 8G+ input of a DM receiver or other DM device, or to an HDBaseT device, via CAT5e, Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA cable - Controls and Indicators:
•PWR: (1) Bi-color green/amber LED, indicates operating power supplied from power pack, turns amber while booting and green when operating
•HDMI INPUT: (1) Bi-color green/amber LED, green indicates a source is detected with a video signal present at the HDMI INPUT port, amber indicates a source is detected without a video signal present
•HDMI OUTPUT: (1) Bi-color green/amber LED, green indicates a sink is detected and a video signal is being transmitted at the HDMI OUT port, amber indicates a sink is connected but a video signal is not being transmitted
•DM OUTPUT 1 – 4 (front): (4) Bi-color green/amber LED, green indicates a link is detected and a video signal is being transmitted at the corresponding DM OUTPUT port, amber indicates a link is detected but a video signal is not being transmitted
•LAN (rear): (2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity
•EDID (rear): (1) 2-position slide switch, DEFAULT position sends a predefined EDID to the HDMI INPUT port [2-channel LPCM audio, 1920x1080 at 60Hz (preferred), 1920x1080 at 30Hz, 1280x720 at 60Hz, 720x480 at 60Hz], COPY 1ST position copies the EDID from a device connected to the HDMI OUTPUT 1 port to the HDMI INPUT port
•HDCP (rear): (1) 3-position slide switch, selects the HDCP version (OFF, 1.4, or 2.2)
•SETUP (rear): (1) Red LED and (1) recessed pushbutton for firmware update
•DM OUTPUT 1 – 4 (rear): (8) LEDs, green LEDs indicate DM link status and amber LEDs indicate video and HDCP signal presence for each corresponding DM OUTPUT port - Power:
•Power over DM (PoDM): IEEE 802.3at compliant PoDM+ PSE (Power Sourcing Equipment), each DM OUTPUT port supplies up to 30 Watts to power one PoDM (Class 0-3) or PoDM+ (Class 4) PD (Powered Device)
•Power over HDBaseT: IEEE 802.3at PoE+ compliant PSE (Power Sourcing Equipment), each DM INPUT/OUTPUT port supplies up to 30 Watts to power one HDBaseT PoE or PoE+ PD (Powered Device)
•PoDM Power Supply: Compatible with model PW-4830DUS or DM-PSU-3X8-RPS (each sold separately)
•Power Consumption: 102W peak with four DM-RMC-4K-SCALER-C receivers connected and powered via PoDM, 33W typical with four DM-RMC-4K-100-C receivers connected and powered via PoDM, 16W idle with no connections - Environmental:
•Humidity: 10% to 90% RH (non-condensing)
•Heat Dissipation: 346 BTU/hr peak with four DM-RMC-4K-SCALER-C receivers connected and powered via PoDM, 111 BTU/hr typical with four DM-RMC-4K-100-C receivers connected and powered via PoDM, 55 BTU/hr idle with no connections - Enclosure:
•Chassis: Metal, black finish, vented sides
•Front Panel: Metal, black finish with polycarbonate label overlay
•Mounting: Freestanding, under-table mountable, or 1 RU half-width 19-inch rack-mountable
24VDC/1.25A Wall Mount Universal Power Pack, 2.1mm
UTK-1U-HALF
Under-table Mounting Kit for 1RU Half-width Devices
ST-RMK
Rack Mount Kit for Control Modules and Tuners
Code3AV Inc.
14201 Justice Rd
Suite B
Midlothian, VA 23113
USA
(804) 223-2990
https://www.code3av.com/